top of page

2150cc Ford Shelby GT500 (07-14) / GT40 (05-06) FIC's Data Matched high performance fuel injectors featuring high impedance bosch core, E85 compatible, with a lifetime warranty.

This massive high performance injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECU?s ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.
Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90 degrees F fuel temperature using CF-16B calibration fluid.

CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to r

2150cc FIC Injector Set | Shelby GT500 (07-14) & Ford GT (05-06)

SKU: FIC-IS404-2150H
$1,623.00Price

    Login to add products to your wishlist

    Login to add products to your wishlist

    Product Reviews

    average rating is 3 out of 5, based on 150 votes, Product ratings

    98% would recommend

    Thank you for your review.

    Cj Napier

    average rating is 5 out of 5

    Aug 17, 2022

    NA King

    I have used all of the big name tuners before I came across Ortiz and ran the fastest times I ever have, with Ortiz. . I ran my fastest time in much worse DA as well, compared to the other 2 big names. Don't waste your money like I did and go directly to the source of the fastest NA cars around!

    I recommend this product.

    SeanDev

    average rating is 5 out of 5

    May 27, 2022

    Installed on 2018 Taurus SHO

    Pump works great. To anyone who might want to save some cash and want a plug-in play install then order this fuel pump from 1A Auto
    2018 Ford Explorer V6 3.5L Turbo Passenger Side Fuel Pump Module Assembly TRQ FPA72032. Its a simple replacement. Pumps are same size, no boring/sanding ridge to make pump fit. No splicing of wires either, connector from 1A Auto is plug and play. Just reuse spacer on pump and use one of the new o-rings and your done. Took me 30 minutes. I swapped out float with OEM, explorer and SHO floats are different. Only pain is retainer on rod on housing, its plastic and you will need needle nose plyers to get it off.

    I recommend this product.

    Martha Gomez

    average rating is null out of 5

    Apr 18, 2022

    Question

    They are 2 injector’s, how many they are.?

    I recommend this product.

    Crazy Cooter

    average rating is 5 out of 5

    Apr 8, 2022

    LOVE THE E85 KIT!

    I bought the E85 conversion kit for my 3.7 from Ortiz Performance (OP) for a couple reasons. First, they specialize in the Cyclone whereas a lot of tuners don't want to bother tuning it (...cause what's the point?). Second, I talked via email at great length with one of their tuners, Lee Ament, and he was happy to take all the time I needed answering questions with detailed answers. Because of the amount of service I received before I purchased, I was convinced that I would be in good hands. I also liked that their favored injector (in the kit) is a genuine Ford part (OEM for the GT500).

    I could tell right away that the OP gas tune was superior to the canned, Bama tunes I was using previously. I could immediately feel that shifts were taking 1/3 less time to complete and I could feel a lot of throttle boost across all rpm and especially in 1st gear (low rpm). I remember asking Bama to add more throttle boost to my tune and they simply don't make changes like that.

    The E85 tune was great. Instant 10%-15% power boost and response across all rpm and really fills in the gap at lower rpm. Feels like I'm using a throttle booster, but I'm not.

    There's only so much you can do to a Cyclone without forced-induction and E85 is a welcome, significant improvement if you already have everything else.

    Installation is straight-forward, you can find a number of videos on YouTube that show exactly how to do this.

    The one important thing to note: These injectors are taller than the stock injectors and
    will not fit deep enough into the fuel rail UNLESS you do not use the stock fuel-injector clips!...which is completely OK! OP and all the above-mentioned videos will also state this. You will probably need a spacer (like a washer) on the 4 fuel rail bolts to fill a small gap. (If you don't pull the injector clips, the fuel rail will make contact with the manifold.) It will also run like crap until you put your first OP tune on it.

    I recommend this product.

    Robert J

    average rating is 5 out of 5